CB77 exhaust down pipes

G-Man · Post by **G-Man** » Mon Dec 04, 2017 4:43 pm

LM

This set was free because I supplied examples. I think they would run to $100-150 depending on numbers. Need to find somer time to check the fit and get some more sets organised.

We supplied good CA and CB masters so a friend and I got two sets each.

G

LOUD MOUSE wrote:What did a set cost ya?. .................lm

G-Man wrote:We're all searching in a constantly diminishing supply.....

I had some stainless pipes made last year.....

G

Jefft wrote:The used stuff on eBay is generally junk and most really needs to go in a dumpster. I check frequently. I‘ve bought reproduction pipes off eBay, two sets , and they are very poorly made. I could spot the aftermarket down pipes from across the street. I was hoping to find a like minded enthusiast that might have one or a pair of surplus pipes to sell.

LOUD MOUSE · Post by **LOUD MOUSE** » Mon Dec 04, 2017 5:10 pm

From whay I can see they look really good.
I sent many old issue parts to Terry and Carol in Washington State and they produced the speedo rubbers, air cleaner rubber foot pegs and not many here are aware that every time I sent a NOS/OEM I never got them back.
What did happen is/was others were/are able to get perfect repo parts. .................lm

G-Man wrote:LM

This set was free because I supplied examples. I think they would run to $100-150 depending on numbers. Need to find somer time to check the fit and get some more sets organised.

We supplied good CA and CB masters so a friend and I got two sets each.

G

LOUD MOUSE wrote:What did a set cost ya?. .................lm

G-Man wrote:We're all searching in a constantly diminishing supply.....

I had some stainless pipes made last year.....

G

Jefft wrote:The used stuff on eBay is generally junk and most really needs to go in a dumpster. I check frequently. I‘ve bought reproduction pipes off eBay, two sets , and they are very poorly made. I could spot the aftermarket down pipes from across the street. I was hoping to find a like minded enthusiast that might have one or a pair of surplus pipes to sell.

G-Man · Post by **G-Man** » Mon Dec 04, 2017 5:24 pm

LM

Yes I think we should all be grateful to people who have given up their parts for reproductions to be made. I have been too busy to push forward with the pipes this year but I intend to get stuck in with some more next year. The ones we had made have not been cut to length so I need to see them on a bike or two before we go ahead.

The firm produces really good quality work and are upt to the job of making them. More news in the New Year, hopefully.

G

LOUD MOUSE wrote:From whay I can see they look really good.
I sent many old issue parts to Terry and Carol in Washington State and they produced the speedo rubbers, air cleaner rubber foot pegs and not many here are aware that every time I sent a NOS/OEM I never got them back.
What did happen is/was others were/are able to get perfect repo parts. .................lm

G-Man wrote:LM

This set was free because I supplied examples. I think they would run to $100-150 depending on numbers. Need to find somer time to check the fit and get some more sets organised.

We supplied good CA and CB masters so a friend and I got two sets each.

G

LOUD MOUSE wrote:What did a set cost ya?. .................lm

G-Man wrote:We're all searching in a constantly diminishing supply.....

I had some stainless pipes made last year.....

G

Jefft wrote:The used stuff on eBay is generally junk and most really needs to go in a dumpster. I check frequently. I‘ve bought reproduction pipes off eBay, two sets , and they are very poorly made. I could spot the aftermarket down pipes from across the street. I was hoping to find a like minded enthusiast that might have one or a pair of surplus pipes to sell.

LOUD MOUSE · Post by **LOUD MOUSE** » Mon Dec 04, 2017 5:40 pm

I'd say that is the best. most correct , smooth bend I've seen. .....................lm

G-Man wrote:LM

Yes I think we should all be grateful to people who have given up their parts for reproductions to be made. I have been too busy to push forward with the pipes this year but I intend to get stuck in with some more next year. The ones we had made have not been cut to length so I need to see them on a bike or two before we go ahead.

The firm produces really good quality work and are upt to the job of making them. More news in the New Year, hopefully.

G

LOUD MOUSE wrote:From whay I can see they look really good.
I sent many old issue parts to Terry and Carol in Washington State and they produced the speedo rubbers, air cleaner rubber foot pegs and not many here are aware that every time I sent a NOS/OEM I never got them back.
What did happen is/was others were/are able to get perfect repo parts. .................lm

G-Man wrote:LM

This set was free because I supplied examples. I think they would run to $100-150 depending on numbers. Need to find somer time to check the fit and get some more sets organised.

We supplied good CA and CB masters so a friend and I got two sets each.

G

LOUD MOUSE wrote:What did a set cost ya?. .................lm

G-Man wrote:We're all searching in a constantly diminishing supply.....

I had some stainless pipes made last year.....

G

Jefft wrote:The used stuff on eBay is generally junk and most really needs to go in a dumpster. I check frequently. I‘ve bought reproduction pipes off eBay, two sets , and they are very poorly made. I could spot the aftermarket down pipes from across the street. I was hoping to find a like minded enthusiast that might have one or a pair of surplus pipes to sell.

cknight · Post by **cknight** » Mon Dec 04, 2017 6:15 pm

Looking good! Please keep us informed. Regards, Chase

John Watson · Post by **John Watson** » Wed Dec 06, 2017 8:16 am

Graham, just a thought, they weren't manufactured in Whitehaven by any chance, were they?

Seadog · Post by **Seadog** » Wed Dec 06, 2017 10:28 am

I’d be in for a set, G.